Skip to main content
Crochet · Reference

Crochet Hook Sizes: Metric and US Reference

Match crochet hook diameters in millimeters to published US labels, with ambiguous sizes and measuring limits explained.

In this guide

    Use the millimeter diameter to match a crochet hook, then use its US marking as a secondary label. Letters and numbers vary between manufacturers. The reference below lists the Craft Yarn Council’s published metric/US associations; a dash means that this source supplies no US marking at that diameter, not that the tool cannot exist.

    Regular crochet hooks: CYC metric/US reference
    Diameter (mm) US marking
    2.25 B-1
    2.5 —
    2.75 C-2
    3.125 D
    3.25 D-3
    3.5 E-4
    3.75 F-5
    4 G-6
    4.25 G
    4.5 7
    5 H-8
    5.25 I
    5.5 I-9
    5.75 J
    6 J-10
    6.5 K-10½
    7 —
    8 L-11
    9 M/N-13
    10 N/P-15
    11.5 P-16
    12 —
    15 P/Q
    15.75 Q
    16 Q
    19 S
    25 T/U/X
    30 T/X

    What the columns tell you

    Millimeters describe diameter, not tool length or stitch gauge. US letters and numbers are names for sizes, not a calculation scale: US 8 is not 8 mm, and a difference of one US number does not mean a one-millimeter change. Multiple metric entries can share a US label. These are published associations for identification, not evidence that tools with the same letter or number are physically identical.

    A crochet hook with arrows marking the full parallel shaft rather than the tapered tip.
    Original enlarged measuring-location schematic. It cannot measure your tool from a screen; use a suitable physical gauge.

    Read an actual pattern and package

    Start with the pattern’s millimeter value. Find that exact value on the package or manufacturer’s size chart, and check it again on the tool if marked. For example, G appears at both 4 and 4.25 mm in the source chart; the label G alone is insufficient to choose between them. If the pattern supplies only an ambiguous US label, consult the publisher or its original materials list before buying a replacement.

    Identify an unmarked tool

    Use a gauge designed for the tool and its size range. The hook head, throat and handle can all be wider or narrower than the working shaft, so an ordinary needle-hole gauge may not accept the head or measure the right place. Use a suitable hook gauge or a reliable manufacturer reference; do not force the head through a hole. If the marking and gauge disagree, check for wear, coatings and gauge tolerances rather than silently relabeling the tool.

    Separate size identification from fabric gauge

    The right marked size is only the starting tool. Make a sample larger than the measuring area in the project’s actual stitch pattern, finish it as the yarn label and pattern permit, then measure a central span without stretching. More stitches in a fixed width mean smaller stitches; trying a larger diameter may help. Fewer stitches mean larger stitches; try a smaller diameter. Repeat the sample, because tension and construction can change the outcome. Check row gauge separately; a correct stitch gauge does not guarantee the required length.

    Scope and exceptions

    This chart is for regular hooks, not the separate steel-hook/thread system. Steel hooks use another numbering convention, so do not carry a bare steel number into this table. Tunisian crochet also needs a hook with enough working length for its live loops; matching diameter alone does not choose the correct construction. If substituting materials or a new brand mid-project, compare washed samples before continuing a fitted piece. Keep the diameter, manufacturer and sample measurements in your project notes so the choice is reproducible.

    Next, use the crochet gauge calculator to interpret a measured sample. The calculator cannot identify a tool from its US marking or replace a pattern’s shaping instructions.

    Keep your project moving

    Start with your swatch.

    Estimate starting chains and fit them to a stitch-pattern repeat using your measured gauge.

    Explore the planning tool

    Sources & editorial notes